
 _    ______  ____                      
| |  / / __ \/ __ \____  ____  ____ ___ 
| | / / /_/ / /_/ / __ \/ __ \/ __ `__ \
| |/ / _, _/ _, _/ /_/ / /_/ / / / / / /
|___/_/ |_/_/ |_|\____/\____/_/ /_/ /_/ 
                                        
Have fun. Please share our work around :)
                                                               
**********\ www.HDfury.com /************





 _     _  _____   ______  ______ _______ ______  _______
 |     | |_____] |  ____ |_____/ |_____| |     \ |______
 |_____| |       |_____| |    \_ |     | |_____/ |______


### HOW TO UPGRADE ###

Please refer to usermanual: www.hdfury.com/docs/HDfuryVRRoom.pdf

We always recommend resetting all settings after each update in case of any issue.
You do it by clicking both checkboxes on RESET area in webserver > config and then type RESET
or you can do it via IP/RS232 with "factoryreset" command. e.g. #vrroom set factoryreset 
or just "set factoryreset" via IP

Please don't forget that you can EXPORT your config BEFORE update and IMPORT it back AFTER update.
This way you won't have to redo any settings.


### Make sure to refresh your browser after update: CTRL + F5 or clear your browser internet cache ### 





 _______ _     _ _______ __   _  ______ _______              _____   ______
 |       |_____| |_____| | \  | |  ____ |______      |      |     | |  ____
 |_____  |     | |     | |  \_| |_____| |______      |_____ |_____| |_____|


########> What's new/fixed in 0.24

1. Audio improvements

2. ATV channel status fixes

3. eARC speakers maps as new option under CEC page (correction for incorrect marking from TV)

4. Front page change to print where audio comes from

5. earcst/arcst tell which one is active or if neither then HDMI is.

6. internal changes

7. Custom HDR injection automatically OFF if signal is VRR

Note: Reboot needed after firmware flash (or TV power cycle) because TV CEC does not get refreshed unless physical TX0 cable is unplug or unit rebooted.






########> What's new/fixed in 0.23

1. The locktime should be much faster so audio should come out quick

2. Sonos & AVR should now get the proper routing changes and request system audio commands to wakeup and change channel

3. Added another selector for eARC unmute timeout so user can fine tune delays more

4. Some incremental fixes on reporting

5. There was a bug in eARC CDS detection for AVR, fixed.

6. DFHD 1080/1200/1440 detection as well 

7. SINK  EDID 420 / 444 reporting (to know at first sight if input is limited or not on TV)

8. Cosmetics changes asked by users

Note: There is known issue on RS232 commands, will be corrected on FW 0.24



########> What's new/fixed in 0.22

1. Fixed a condition in matrix mode when "copy TX0" or "copy TX1" input port selector option was not retained after switching input

2. Fixed a rare condition at startup when signal could be limited to 4K120 420 8b

3. Improved support for PC GPU when mode change or input switching

4. Added HDCP version reporting on signal info

5. eARC related changes and internal mods

6. Fixed reporting for outgoing bandwidth "0 MHz" 

7. Added "Request Audio Mode" and "Request Audio mode + Routing Change" under CEC page > Audio Out Zone

Note: An AVR needs to be in audio system mode in order to accept volume commands. This is why we cannot just keep a simple power on/off toggle.
"Request Audio Mode" alone should not cause any port changes to the channel we are sending from.
Whereas the second "Request Audio Mode + Routing Change" will change AVR to the port.




########> What's new/fixed in 0.21

1. Added routine for Samsung Q90/QN900/QN95 and similar Samsung models to offer true FRL/VRR/ALLM from Xbox series S/X and FRL/ALLM from PS5

2. Added routine to prevent sound system to turn ON or switch TV input via CEC when system is turned off.




########> What's new/fixed in 0.20

1. Fixed Atmos/DD+ descriptors for Samsung/Sony via ARC

2. Added more setting on the CEC page for AUDIO OUT zone power up/down control. Here you can disable and enable power upping. We will add some more modes later for different types of power up

3. Improved eARC / HDMI switching between sound from TV eARC and sound from HDMI sources at inputs

4. Added the indivudual CEC control for each input port on the CEC page

Note 1 : Added indicator for HDMI / EARC mode but still in progress. Info about it on the OLED page 3 where the RX info is
Note 2 : Default HDCP settings after firmware flash is AUTO, if you import a config exported on previous firmware, please verify HDCP remains set as AUTO after import.




########> What's new/fixed in 0.19

1. Added CEC information on the CEC page

2. Added ARC/eARC TX selector under CEC page (must be set to ARC if ARC sound system is connected at eARC OUT)

2. Added ARC/beam1 and ARC/dd+ option under audio caps in AUTOMIX

4. Added logic around audio out- power up and down

Please note that eARC OUT is now default for AUDIO CAPS under AUTOMIX (you might want to change it to AUDIO OUT if you use AUDIO OUT to your sound system HDMI INPUT).




########> What's new/fixed in 0.18

1. Corrected HDR EDID detection bug in Automix mode that manifested on FW 0.17 (AUTOMIX = COPY TX SINK EDID and MODIFY)

2. Added UNMUTE delay option. Note that it is still under testing, can be set if user hears crackle or pop sound when switching audio format (starting/stopping content/app)




########> What's new/fixed in 0.17

1. Fixed html issues in webserver when monitor edid has specific block (LG 27GP950-B)

2. Fixed config export parameters

3. Added some audio-related reporting fixes



########> What's new/fixed in 0.16

1. Added RS232 commands 



########> What's new/fixed in 0.15

1. Release version 






 ****************************************************
 __  __   ____        ___                             
/\ \/\ \ /\  _`\    /'___\                           
\ \ \_\ \\ \ \/\ \ /\ \__/  __  __   _ __   __  __   
 \ \  _  \\ \ \ \ \\ \ ,__\/\ \/\ \ /\`'__\/\ \/\ \  
  \ \ \ \ \\ \ \_\ \\ \ \_/\ \ \_\ \\ \ \/ \ \ \_\ \ 
   \ \_\ \_\\ \____/ \ \_\  \ \____/ \ \_\  \/`____ \
    \/_/\/_/ \/___/   \/_/   \/___/   \/_/   `/___/> \
                                                /\___/
                                                \/__/
*****************\ www.HDfury.com /*******************


Need a discount code ? Share a link to us, write a review, 
tell people on any forum how cool we are and you will be rewarded with discount code!
the more you do, bigger will be the discount, do something amazing and get a FREE HDFURY!

